Just How to Remove as well as Change a Tub.
Just How to Remove as well as Change a Tub.
Blog Article
Right here below you can get a bunch of extremely good data concerning How to Install a Bathtub.
:max_bytes(150000):strip_icc()/convert-tub-to-shower-4156975-05-db9a69eb718545759045e6e39b4cfacf.jpg)
Setting up a bathtub isn't specifically rocket science, yet it does need strong plumbing, carpentry, and also often, tiling abilities. Replacing an old bathtub with a brand-new one is also a reasonably challenging task. If the old bathtub is readily easily accessible, the project can relocate quickly; if you need to open a wall surface to eliminate the old bathtub as well as place the new bath tub, the task is a lot harder. In either case, the task is within a home handyman's abilities, although you will require a helper to leave the old bathtub as well as embeded in the new one. See to it you have qualified on your own for the job and also are comfortable trying it. Rather than employing a contractor to take control of a halfway-completed task, it is better to take into consideration utilizing one prior to you begin. Possibilities are you might need an expert plumber to make tube links.
This short article will certainly aid you set up a brand-new bath tub in your restroom if you have actually currently purchased a brand-new bathtub and don't require to change the arrangement of your previous water system pipelines.
Your tools as well as product list ought to make up the following:
Planning for the Installation
First of all, the sustaining frame provided with the bathroom should be fitted (if needed) according to the supplier's instructions. Next off, fit the faucets or mixer to the bathtub. When fitting the faucet block, it is important to ensure that if the tap features a plastic washing machine, it is fitted between the bath and also the faucets. On a plastic bath, it is likewise practical to fit a sustaining plate under the taps unit to avoid pressure on the bath tub.
Fit the flexible tap ports to the bottom of both faucets using 2 nuts as well as olives (often provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and after that pass the electrical outlet through the hole in the bath. Use the nut supplied by the maker to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the versatile overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bath. Make sure you use all of the supplied washers.
Link the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Attach all-time low of the overflow tube in a comparable manner.The bathroom need to currently prepare to be suited its last placement.
Removing Old Taps
If you need to replace old taps with new ones as a part of your installation, then the first thing you should do is disconnect the water supply. After doing so, turn on the taps to drain any water remaining in the system. The process of removing the existing faucets can be fairly bothersome as a result of the limited accessibility that is commonly the instance.
Utilize a container wrench (crowsfoot spanner) or a tap tool to undo the nut that connects the supply pipelines to the faucets. Have a towel prepared for the staying water that will come from the pipes. Once the supply pipelines have actually been eliminated, use the same device to loosen up the nut that holds the faucets onto the bath/basin. You will need to stop the solitary faucets from turning during this process. As soon as the faucets have been removed, the holes in the bath/basin will need to be cleansed of any type of old sealing compound.
Prior to carrying on to fit the new faucets, contrast the pipeline connections on the old faucets to the brand-new taps. If the old taps are longer than the brand-new faucets, then a shank adapter is required for the brand-new faucets to fit.
Installing the Bathtub
Making use of both wooden boards under its feet, place the bath tub in the required setting. The wooden boards are handy in uniformly spreading the weight of the bath tub over the location of the boards rather than focusing all the weight onto 4 little points.
The following objective is to guarantee that the bath tub is leveled all round. This can be accomplished by inspecting the level as well as adjusting the feet on the bath tub up until the spirit level reviews level.
To install faucets, fit the bottom of the outermost versatile faucet port to the appropriate supply pipeline by making a compression join; after that do the exact same for the other faucet.
Switch on the water as well as check all joints as well as new pipework for leakages and tighten them if essential. Fill up the bath tub and also inspect the overflow outlet as well as the normal electrical outlet for leaks.
Lastly, fix the bathroom paneling as described in the maker's instruction manual. Tiling and also sealing around the bath tub should wait up until the bathtub has actually been used a minimum of when as this will resolve it into its last position.
Fitting New Touches
If the tails of the new faucets are plastic, then you will require a plastic connector to avoid damages to the thread. One end of the adapter fits on the plastic tail of the tap as well as the various other end offers a link to the existent supply pipes.
If you require to fit a monobloc, then you will call for decreasing couplers, which links the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
Next, position the faucet in the placing hole in the bath/basin making sure that the washing machines remain in place between the tap as well as the sink. Safeguard the faucet in place with the manufacturer offered backnut. When the faucet is firmly in position, the supply pipes can be linked to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with regular tap connectors. The former kind needs to be connected to the tap ends initially, tightening up only by hand. The supply pipes can later be linked to the various other end. Tighten up both ends with a spanner after both ends have been connected.
Tiling Around the Tub
In the location where the bathroom meets the ceramic tile, it is needed to secure the accompanies a silicone rubber caulking. This is important as the fitting can move enough to split an inflexible seal, creating the water to pass through the wall between the bath as well as the tiling, causing problems with moisture as well as feasible leakages to the ceiling listed below.
You can pick from a selection of coloured sealers to blend in your fixtures and fittings. They are sold in tubes and cartridges, and are capable of sealing gaps up to a width of 3mm (1/8 inch). If you have a larger gap to fill, you can fill it with twists of soaked newspaper or soft rope. Remember to always fill the bathtub with water before sealing, to allow for the activity experienced when the bathtub remains in usage. The sealer can split rather very early if you do not take into consideration this motion before sealing.
Alternatively, ceramic coving or quadrant floor tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are likewise easily readily available on the marketplace. It is advisable to fit the floor tiles utilizing water-resistant or water-proof sticky as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As an avid reader on How to Install a Bathtub Yourself, I thought sharing that excerpt was beneficial. So long as you appreciated our blog posting please do not forget to share it. I praise you for your time. Don't forget to come visit our site back soon.
Explore Report this page